Similar Topics: Cable Assembly
Cable Assemblies
enable IO signal paths.
See Also: Cables, Interconnects, Flying Leads, Instrument Cables, Patchcords
-
product
SH25M-10F Cable, 25-Pin Male D-SUB to 10-Pin Female COMBICON, Shielded Multifunction Cable
190654-02
25-Pin Male D-SUB to 10-Pin Female COMBICON, Shielded Multifunction Cable - The SH25M-10F Cable, sometimes referred to as SH10F-25M, connects C Series DAQ devices with a 10-pin screw terminal to a 25-pin D-SUB. The SH25M-10F Cable is offered in different lengths.
-
product
I/O Wiring Cable
PCL Series
I/O wiring cable sets are designed for easy field wiring capabilities. The PCL-1050 I/O wiring cable series can be used with multiple I/O cards.
-
product
Cable 100-Pin Micro-D Male To Unterminated, With Ferrules, 1m 2-56 UNC Screwlocks, Metal Shell
A100SMR-F-9B100
100-Pin Micro-D Male to Unterminated Cable Assembly With Ferrules, 1m Long With 2-56 UNC Screwlocks and Metal Backshell. Suitable for use with Pickering BRIC Modules.
-
product
20-Pin GMCT Cable, Male to Male, 10A, 0.5m
A020GMR-020GMR-0B050
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 20-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Cable Test Van
Titron
BAUR Prüf- und Messtechnik GmbH
Automatic cable test van. The BAUR titron is a new automatic cable test van designed for cable fault location and cable testing. The new generation of the high-performance cable test van is based on state-of-the-art technology and provides effi cient, safe and reliable cable fault location and cable testing.* New intuitive operational concept* Central, automatic system control* Top reliability and quality standard* Flexible in terms of technology and equipment
-
product
AC Current Probe 2 mV/A, 3,000A, 0.11 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil
T3RC3000-LF
AC Current Probe 2 mV/A, 3,000A, 0.11 Hz LF Bandwidth, 6.5MHz HF Bandwidth, 4m cable, 300mm coil.
-
product
SHC68-NT-S, 68-Pin VHDCI Female to 68-Pin Bare Wire Male Multifunction Cable
189041-02
SHC68-NT-S Shielded Cable for 7831R boards, 68-pin VHDCI to unterminated, 2m
-
product
Analog Control Cable for Electronic Loads
EE105T-xx
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
product
HD BNC Male to BNC Male Cable, 50 Ohm, 1 m
784996-01
The HDBNCM-BNCM Coaxial Cable connects measurement and signal generation devices.
-
product
Cable Continuity Tester, Auto Ranging, 4000 Count Display
72-9170
Quickly identify wires and tests continuityFits in any pocket or tool kit Invaluable in all audio, video, network, telecom and electrical installations
-
product
3-Pin Power D-Type Cable, Male to Male, 2m
40-970-403-2m-MM
The 3-Pin Power D-Type cable assembly is constructed from 50/0.26mm2 (14 AWG) Tinned Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
20-Pin GMCT Cable, Female to Unterminated, Ferrules, 10A, 0.5m
A020GFR-F-0C050
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
product
50-Pin IDC Connector for Ribbon Cable - Male
40-961-550-M
Ideal for user created termination schemes where the termination is to be remotely connected by a ribbon cable.
-
product
High Speed Cable Production Tester
GRL-V-DI20
GRL-V-DI20 provides a fast and easy way for anyone to test cables for manufacturing defects and signal integrity specification requirements. GRL-V-DI20 provides comprehensive test coverage in seconds at a fraction of the cost of similarly-capable bench test equipment.
-
product
SH96F-96M-5, Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 3 Meter
786341-03
Shielded Cable for PXIe-4330 and PXIe-4331 to Rackmount Terminal Block, 3 Meter
-
product
ITA, i2 MX, EMI Backshell, with Cable Exit (Shell only, does not include front protective cover or modules)
410130114
ITA, i2 MX, EMI Backshell, with Cable Exit (Shell only, does not include front protective cover or modules)
-
product
Semi-Rigid Cable, 3.5 Mm (Test Port) To 3.5 Mm
85131C
The Keysight 85131C is an 81 cm (32 in) long1 semi-rigid cable with a 3.5 mm female2-to-PSC-3.5 mm female connector. Cable frequency range is DC to 26.5 GHz with a return loss of 17 dB or better. Insertion loss is 0.43 * sqrt(f) + 0.3, where f is frequency in gigahertz, for the test port connector and 2.5 dB at maximum frequency for the device connector. Phase stability of the semi-rigid / flexible cables is specified with a 90-degree bend using a 4 to 3-inch radius. Stability1 of the 85131C is less than 0.06 dB, and phase is 0.16 * f + 0.5, where f is frequency in gigahertz.
-
product
Handheld Cable and Antenna Analyzer
ZVH
The R&S®ZVH is a rugged, handy cable and antenna analyzer, designed for use in the field. Its low weight and simple operation make it indispensable for anyone who needs an efficient measuring instrument outdoors for the installation and maintenance of antenna systems.
-
product
1kV, 80 MHz High Voltage Differential Probe with 6m Cable and Auto Zero Disconnect
HVD3106A-6M
The HVD3000A series of high voltage differential probes cover the fullest range of applications, from 120/240 V switch-mode power supplies through 600 V class and 5 kV electrical apparatus. The table below provides a list of recommended probe models based on specific device under test applications.
-
product
CB-50 I/O Connector Block with DIN Rail Mounting without cable
776164-90
50-Pin Male IDA to 50-Pin Female Screw Terminal, DIN Rail, Terminal Block - The CB-50 provides 50 screw terminals for connection to I/O signals from your 50-pin NI data acquisition devices. The CB-50 includes one 50-pin header for direct connection to 50-pin cables. It features a protective plastic base and hardware for mounting on a DIN Rail.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends
A050DF4-T-0A050
The 50-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated wire and can be secured to the product by screwlocks. The 50-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
ARINC 615/615A USB Smart Cable PDL Solution
uPDL-615
Avionics Interface Technologies
The AIT Micro Portable Data Loader (uPDL-615) is a ruggedized, portable “intelligent cable” solution that can be used in conjunction with a USB connection to any Windows PC, Laptop, or Tablet to support ARINC 615, ARINC 615A, and ARINC 844 software data load applications.
-
product
Cable 100-Pin Micro-D Male to Unterminated, Cut Ends, 1m 2-56 UNC Screwlocks, Metal Shell
A100SMR-C-9A100
This 1m long male to unterminated 100-Pin SCSI Style Micro-D Cable Assembly is suited for direct connection to various products using the 100-Pin connector. It is constructed from 100-Pin twisted pair cable with varying left and right hand lays to minimise crosstalk. The Cable is colour coded to ensure easy connection. Screwlocks are provided to secure the SCSI connector to its associated product.
-
product
MCX Male to BNC Male Cable, 50 Ohm, 1 m
188375-01
The MCX-BNC Coaxial Cable is used for modular instruments such as PXI switches. This cable is available in 1 m and 30 cm lengths.
-
product
Cable 96-Pin Female to 100-Pin Male Micro-D, 1m
40-973B-096-1m-FM
The 96-Pin to 100-Pin SCSI Style Micro-D Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
product
Low Leakage Triaxial Cable (0.4m / 0.8m / 1.5m / 3m / 4m)
16494A
16494A is suitable for low current applications down to the sub fA level. It supports a maximum voltage/current of 200 V / 1A DC.
-
product
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" Depth
410112702
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" DepthIncludes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With cable clamps in open position- stiffener bar may be removed to allow installation or removal of cables without requiring wiring to be disconnected from the assembly.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
product
Cable Assy 78-Pin D M/M 2m
40-970-078-2m-MM
A 78-Pin D-Type cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable to its associated products. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
Semiconductor Assembly
With the know-how that we have cultivated over many years in the semiconductor manufacturing process, we respond to the diverse needs of our customers regardless of prototype production and mass production.
-
product
Cable Assy 26-Pin D-Type F/F 0.5m
40-970-026-0.5m-FF
The 26-Pin D-Type cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products. The 26-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
